Zipato Zipabox Installationsanleitung PDF herunterladen

make your home smart www.zipato.com make your home smart www.zipato.com

TRADEMARKS

Zipato and the Zipato logo are registered Trademarks. All

other product names mentioned herein may be trademarks or

registered trademarks of their respective companies.

NOTICE

Although Zipato has attempted to ensure the accuracy of the

content of this manual, it is possible that this document may

contain technical inaccuracies, typographical, or other errors.

Zipato assumes no liability for any error in this publication, and for

damages, whether direct, indirect, incidental, and consequential

or otherwise, that may result from such error, including, but not

limited to loss of data or proﬁ ts. Zipato provides this publication

“as is” without warranty of any kind, either express or implied,

including, but not limited to implied warranties of merchantability

or ﬁ tness for a particular purpose. The published information in

the manual is subject to change without notice. Zipato reserves

the right to make changes in the product design, layout, and driver

revisions without notiﬁ cation to its users. This version of the

Installation guide supersedes all previous versions.

ELECTROMAGNETIC COMPATIBILITY

In proper state and when operated properly, the product complies with

all the requirements in respect of interference radiation according

to EN 301 489-17, EN 301 489-1 and EN 300 328. The connections

conducting HF signals must neither be manipulated nor damaged.

TAKE CARE OF YOUR SAFETY

Display extreme caution when using ladders or steps, please

follow manufacturer’s instructions. Be careful when using hand

and power tools and follow the manufacturer’s guidelines when

using them. Take care that the correct tools are used. Wear

goggles or protective clothing where required.

INTRODUCTION

TECHNICAL SPECS

NORMAL OPERATING VOLTAGE 2x AA 1,5V batteries

FREQUENCY RANGE 868.42 MHz

RANGE Up to 30m line of sight

PROTOCOLS SUPPORTED

ISO15693, ISO18000-3,

Tag-it™, RFiD

BUZZERSOUND

Approximately 60dBa at

10 cm distance

BASIC OPERATIONS

The Mini Keypad RFiD/Z-Wave can arm/disarm a security system.

The Mini Keypad RFiD/Z-Wave can read Mini Keypad RFiD/Z-

Wave-tags.

The Mini Keypad RFiD/Z-Wave has the possibility for the user to

manually insert codes.

The Mini Keypad RFiD/Z-Wave’s indicator light will react

differently on each action.

The Mini Keypad RFiD/Z-Wave has a buzzer, which can be used as

walk-in/walk-out notiﬁ cation (alarm is being disabled/activated).

MOUNTING

1 | Use a ﬂ at screwdriver at the inlets on the sides to gently unlock

the back cover.

2 | Use the designated holes on the back cover to screw mount the

Mini Keypad RFiD/Z-Wave.

3 | Place two AA 1,5V batteries into the device.

4 | Mount the Mini Keypad RFiD/Z-Wave onto the back cover, be sure

to close it on all sides and that the tamper gets through the back

cover of the Mini Keypad RFiD/Z-Wave. (indication mode: Tamper

pressed/released).

5 | After 1 seconds startup routine begins (indication mode: Ready

for learn mode).

6 | After 3 more seconds (4 seconds in total) mounting is

completed. (indication mode: Mounting successful)

7 | The Mini Keypad RFiD/Z-Wave is now ready to use.

INCLUDE OR EXCLUDE IN ZWAVE NETWORK

1 | Make sure your Z-Wave controller is in the right operation mode

(include or exclude)

2 | Press and hold the tamper for 1 seconds and release to start

the inclusion/exclusion process

(indication mode: Ready for learn mode).

3 | (The product will start NWI automatically after unsuccessful

normal inclusion)

CONTROL

The Mini Keypad RFiD/Z-Wave operates as an access control device,

using the combination of the USER_CODE command class and the

ALARM_V2 command class. UserCodes are to be stored in the Mini

Keypad RFiD/Z-Wave, using the USER_CODE_SET command. When

the UserCodes are stored in the Mini Keypad RFiD/Z-Wave, the

ALARM_REPORT_V2 will have the corresponding USER_ID with the

used USER_CODE.

There are two types of Access Control with UserCodes:

1 | Manually by using the buttons on the Mini Keypad RFiD/Z-Wave

2 | Using the Mini Keypad RFiD/Z-Wave reader and Tags

The difference in using one of the above mentioned methods is:

1 | When pressing Home/Away, the manual codes (1-4) can be pressed

within 1 second. After entering the code the user must press ENTER

and the USER_CODE_REPORT or ALARM_REPORT_V2 will be sent.

2 | When the user waits 1 second after pressing Home/Away, the Mini

Keypad RFiD/Z-Wave reader is started and a Tag can be presented at

the Mini Keypad RFiD/Z-Wave.

After successful read, the USER_CODE_REPORT or ALARM_

REPORT_V2 will be sent.

Because the RFID code are not readable on the Tags, the Mini Keypad

RFiD/Z-Wave has some special procedures. Some examples are given

at the Typical operation diagrams chapter in the Technical Manual.

There are some situations:

1 | IN CASE AN UNKNOWN MANUAL CODE ENTERED OR UN

KNOWN TAG PRESENTED.

In this case, the Mini Keypad RFiD/Z-Wave will send an unsolicited

USER_CODE_REPORT with UserID 0 and UserID Status 0. A

controller will receive this report and can initiate a USER_CODE_SET

to the Mini Keypad RFiD/Z-Wave.

2 | IN CASE A KNOWN MANUAL CODE OR TAG IS PRESENTED.

This means, this code was previously SET using the USER_CODE_

SET command. Then the Mini Keypad RFiD/Z-Wave will respond with

a ALARM_REPORT_V2 with Type 6 and Event 0x05 or 0x06. When the

user presses Home, event 0x06 (Keypad Unlock) will be used. When

the user presses Away, event 0x05 (Keypad Lock) will be used.

INDICATION MODES

The indicator gives various statuses of the device as follows:

1 | Ready for learn mode: Indicator light blinks every second.

2 | Learn in progress (add): Indicator light blinks 2 times per second.

3 | Learn in progress (remove): Indicator light blinks 3 times per second.

4 | Learn mode success: Indicator light is on for 1 second.

5 | Learn mode failed: Indicator light blinks 8 times fast.

6 | Tamper pressed/released indicator light blinks 3 times rapidly.

7 | Mounting successful indicator light is on for 1 second.

8 | Busy sending an RF message Indicator light is blinking each

second, while most of the time on.

9 | RF message send failed indicator light blinks 6 times rapidly

TECHNICAL MANUAL

CAUTION

This device is using a radio signal that passes through walls,

windows and doors. The range is strongly inﬂ uenced by local

conditions such as large metal objects, house wiring, concrete,

furniture, refrigerators, microwaves and similar items. On

average, the indoor range is approximately 30 meters.

Do not expose this product to excessive heat or moisture.

Prevent long term exposure to direct sunlight.

Do not attempt to repair this product. If the product is damaged

or if you are in doubt about the proper operation, take the

product back to the place of purchase.

Do not clean the product with any liquid.

TECHNICAL DETAILS:

NORMAL OPERATING VOLTAGE 2x AAA 1,5V batteries

From 2,3 to 4,0Vdc

do not use rechargeable batteries

FREQUENCY RANGE 868.42 MHz

WIRELESS RANGE Up to 30m in line of sight

PROTOCOLS SUPPORTED ISO15693, ISO18000-3, Tag-it™, RFID

BUZZERSOUND Approx. 60dB at 10 cm distance

STORAGE TEMPERATURE -5 ° C to +65 ° C

STORAGE HUMIDITY 10% to 70%

OPERATING TEMPERATURE 10°C to 40°C

OPERATING HUMIDITY 30% to 80%

SUPPORTING COMMAND CLASSES

BASIC TYPE BASIC_TYPE_ROUTING_SLAVE

GENERIC TYPE GENERIC_TYPE_ENTRY_CONTROL

SPECIFIC TYPE SPECIFIC_TYPE_NOT_USED

LISTENING FALSE, Z-Wave Lib: 4.51

CLASS: 0x85 COMMAND_CLASS_ASSOCIATION

CLASS: 0x80 COMMAND_CLASS_BATTERY

CLASS: 0x84 COMMAND_CLASS_WAKE_UP

CLASS: 0x86 COMMAND_CLASS_VERSION

CLASS: 0x72 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

CLASS: 0x71 COMMAND_CLASS_ALARM_V2

CLASS: 0x70 COMMAND_CLASS_CONFIGURATION

CLASS: 0x25 COMMAND_CLASS_SWITCH_BINARY

CLASS: 0x63 COMMAND_CLASS_USER_CODE

NOT LISTENING ROUTING SLAVE

This Z-Wave product will be used as routing slave. Slave nodes are

nodes in a Z-Wave network that receive commands and perform

actions based on the command. This device will always be in sleep

mode because it works on batteries. In sleep mode the device is not

active listening, the device will wake up according to the wakeup

command class.

INCLUDE INITIATOR

The include initiator is used when Primary and Inclusion Controllers

include nodes into the network. When both the include initiator have

been activated simultaneously the new node will be included to the

network (if the node was not included previously).

EXCLUDE INITIATOR

The exclude initiator is used by Primary and Inclusion Controllers to

exclude nodes from the network. When the exclude initiator and a

slave initiator are activated simultaneously, it will result in the slave

being excluded from the network (and reset to Node ID zero). Even if

the slave was not part of the network it will still be reset by this action.

ZWAVE COMPATIBILITY

Because this is a Z-Wave device, it means it can co-operate with other

Z-Wave devices of other manufacturers. It can co-exist in a Z-Wave

network existing with product from other manufacturers.

HOPS & RETRIES

The Z-Wave range has a range of up to 30 meters in line of sight. This

signal is not limited to the 30 meter range due to routing the Z-Wave

message to other nodes in the network. This way the range of the

Z-Wave network can be expanded to 150 meters indoors (limit of 4 hops).

CLASS: 0X63 COMMAND_CLASS_USER_CODE

The purpose of the User Code Command Class is to conﬁ gure the Mini

Keypad RFiD/Z-Wave to accept certain RFID Tags or codes. This is

typically done by some kind of static controller or gateway (for instance

the Wintop iGate). After sending a User Code Set, including a unique

User Identiﬁ er (UID), the in-use state (0x01) and the Tag code or keypad

sequence using ASCII codes, the Mini Keypad RFiD/Z-Wave will accept

the code and notify any other device using the Alarm Command Class.

This other device can be conﬁ gured using the Association Command

Class and is typically the same controller or gateway. When a tag or

code is not known to the Mini Keypad RFiD/Z-Wave, it will send an

unsolicited report to the devices in its association group with the UID

0x00. The value in this message can be used to conﬁ gure new tags.

NOTE: Code length must be 4 to 10 ASCII digits.

CLASS: 0X86 COMMAND_CLASS_VERSION

This Command Class is used to obtain information about the Mini

Keypad RFiD/Z-Wave. The Z-Wave library type, the Z-Wave protocol

version and the application version will be reported.

CLASS: 0X72 COMMAND_CLASS_

MANUFACTURER_SPECIFIC_V2

This will report information about the manufacturer. This product will

contain the manufacturer ID of Wintop. Manufacturer ID of Wintop is

0x97, the ID of this product is 0x31. This command class can also be

used to request the serialnumber of the device.

CLASS 0X20 COMMAND_CLASS_BASIC

The basic command class only has a supporting role and is

mapped to the Switch Binary Command Class.

CLASS 0X25 COMMAND_CLASS_SWITCH_

BINARY

The Switch Binary Command Class is used to enable or disable

the notiﬁ cation sound. This sound is typically used to notify a user

when the alarm system is being activated. See also the ‘Sound

Notiﬁ cation’ section.

MINI KEYPAD

RFiD/ZWAVE

QUICK INSTALLATION GUIDE

v1.2

Home Away

Enter

1 2 3

7 8 9

Tamper

Switch

Tag

Area

Manual

Code

Buttons

Indicator

LED

Home & Away

Buttons

1 2 3 4

MINI KEYPAD 1
RFiD/ZWAVE 1

Inhaltsverzeichnis

Seite 1 - RFiD/ZWAVE

make your home smart www.zipato.com make your home smart www.zipato.com TRADEMARKSZipato and the Zipato logo are registered Trademarks. All other prod

Seite 2

make your home smart www.zipato.com make your home smart www.zipato.com CLASS: 0X80 COMMAND_CLASS_BATTERYThis class is used to request and report bat

Seite 3

make your home smart www.zipato.com make your home smart www.zipato.comTROUBLESHOOTING FREQUENTLY ASKED QUESTIONSQ | Why doesn’t the Mini Keypad RFiD/

Seite 4

make your home smart www.zipato.com make your home smart www.zipato.comDECLARATION OF CONFORMITYThe Manufacturer Tri plus grupa d.o.o. hereby declares